Dana 30 One Piece Axle Conversion Seal

-diff fluid to replace the stuff you drain during the install. This assembly uses a two-piece long side axle shaft.

Installing Tj D 30 Shafts In A Yj

710068 46470.

Dana 30 one piece axle conversion seal. Steve - the part number is CR11800 CRChicago Rawhide if I remember correctly. I know there are already some write-ups on this but heres how I did it. All the axles are the same length and spline for all Jeep Dana 30s 27 spline.

-a block off plate for the axle disconnect. Since I also bought new axle shafts we replaced the original axle shafts with the new ones at this point. Set seal in seal bore of axle tube See Fig1.

By Ty Cook. Yes its one of a few different seals thatll work at the carrier passenger side when swapping to a 1 piece TJXJchromo style shaft. Jun 26 2010.

Torque to 65-75 ftlb. Jeep XJ Cherokees also used a Dana 30 front axle and some were available with a 1-piece passenger side inner axle instead of the vacuum disconnect 2 piece but I was never able to get a definite answer if they would be a bolt in swap. Tighten nuts while checking.

Torq-Masters XJ and YJ CAD 1 piece axle shaft conversion Kit. TJ XJ non disconnect CJ YJ Non Disconnect WJ - Both Sides Fits. There all the same spline and width.

The Rubicon 44s have 30 spline axles but theyre still the same length as the regular Dana 30s. My driver side seal was leaking pretty bad so I knew I had to fix it and I figured I might as well go to a TJ 1pc shaft while I was in there. The parts you need to do this in a YJ are as follows.

The 2 piece shafts suck stick with the 1 piece shafts. When putting TJ shafts into a YJ you need to put a plate in place of the vacuum. One Piece Axle Conversion Inner Axle Oil Seal AMC 20 LH or RH1976-1.

Hi guys Im piecing together the seals needed to change my 2 piece disconnect passenger axle to a 1 piece TJ axle. Step 1 Buy your parts. Ford 9 Detroit Locker 88 disc brake conversion Currie 31spline shafts anti-wrap bar.

Dana 30 Inner axle Seal for Disco Eliminator Kit or One piece axle conversion on Dana 30 disconnect axles - 200 OD - 1069 ID - 37 Wide. All 1987-1995 YJ Wranglers and many XJ Cherokees came with a reverse-cut Dana 30 front axle that has a Center Axle Disconnect CAD feature. Axle Tube Seal Inner.

1 Napa 11800 These will go in the. Fits most D30 disconnect front axles with 27 splines. 99-05 Ford F250F350Excursion for Dana 5060 SKU.

-both inner and outer axles out of a TJ. This gains me the larger u-joints and eliminates the disconnect entirely. The new shafts are essentially Dana 44 shafts machined to fit the Dana 30 housing.

Steps 10 - 11. Joined Oct 21 2013. Torq-Masters 4340 Chromolly Axle Shafts are an essential upgrade Offroaders looking to get the most out of their vehicle.

I scanned the net and found what I though was good info on the proper seal to use when upgrading a 2-piece Dana 30 axle to a one-piece unit. Rustys Spicer Axle Block Off Plate Seal Kit. Slide large washer onto the rod at the knuckle end and thread nut onto rod.

Check ID of tube to insure proper OD of seal there is a 2062 Seal available as there are some axle tubes where this seal will be to small. We upgraded to 4340 one piece axle shaft and eliminated the disconnect all together. Yes it had the puny u-joints and 2-piece passenger side axle shaft until now.

Take care to avoid damaging the seals when installing the shafts. The new 297x shafts big u joint are what most people want to run. My TJ D30 has the seal at the carrier bearings Dont see why you couldnt go that route I no disconnect axle expert though.

This also includes using Dana 44 u-joints. Or you can be big baller and run RCVs. Install inner seal into axle housing end.

MODEL 20 One-Piece Axle Kit Instructions Continued. Our Heavy Duty shafts are built to such high quality standards that we can offer an exclusive Lifetime Warranty giving you piece of mind in. DANA 30 MANUAL HUB CONVERSION KIT.

CLICK HERE for More Details Part. Attach new outer axle shaft to original inner axle shaft. Dana 30 Inner Axle Seal Fits common D30 Front axles with 27 splines 2131 OD and 1069 ID.

Should be able to use any one piece D30 Shaft Just so your options are wider spread TJ YJ XJ ZJ and so on. Install the rear bearing seal into the conversion hub. 8 May 10 2016.

Dana 30 Detroit Truetrac Rocky Road Outfitters High steer kit and one peice axle shaft conversion. Use a seal installation tool to ensure no damage to seal and seat against shoulder in housing. Warn now offers a kit to convert the axle to a 5 on 5 12 bolt circle using premium hubs and a modified CJ.

So far I have figured out that the inner passenger axle seal I need to install is 1. DANA SPICER 75814-1X LEFT SIDE Axle Assembly fits DANA 30 Disconnect Front 1986 to 1996 Jeep WRANGLER YJ and 1984 to 1991-12 Jeep XJ with NO ABS replaces old number 75587-1X axle - FREE SHIPPING. Install threaded wheel studs in axle flanges with supplied thread locker.

Lo and behold the seal part number info did not work for me. Dana 30 TJ axle shaft conversion seal replacement. Apply a small amount of oil or grease on seal.

This can be easily identified by a medium-size cast housing integrated into the passenger side axle tube. ROCKRIDGE 4WD explains a Jeep Dana 30 Center Axle Disconnect. This kit includes 2 seals and a CAD block off plate.

I am installing CVs from a Grand Cherokee. I have TJ Dana 30 shafts in my YJ.

Amazon Com Yukon Gear Axle Ya D43205 Replacement Outer Stub Axle Shaft For Jeep Wrangler Dana 30 Differential Automotive